Author: admin
Grizzly Industrial H6087 2-Axis Digital Readout (Monitor Only) New, Open Box
New in open box, comes with what is shown including mounting hardware, box, manual, and power cord. This is not the complete system, the encoders are not included.
ONE NEW M503 Magnetoscale LCD Digital Readout Meter for stCutting tool
ONE NEW M503 Magnetoscale LCD Digital Readout Meter for stCutting tool. 1.7 bit LCD display that it is more suitable for long travel equipment. High contrast backlight, clear and eye-catching. Low power consumption, no external power supply (built-in two nodes 5 battery). Repetition precision can be up to + 0.01mm. 5 initial value reset function (“clean zero”). Optional millimeter mm/ inches inch. Optional relative REL/ absolute ABS. Optional linear measurement / angle measurement. System precision: ±0.03+0.01L(m) mm. Resolution: 0.01, 0.05, 0.1, 1. Display range: -1999999 9999999. Consumption of current: Max. Power: two AA battery. Reading head and line length: default 1m. Reading head gap: Max. 2.5mm, recommending 1.5mm. Matching magnetic ruler: MS50. Waterproof grade: digital display IP40, reading head IP65. Ensure the parallelism of the installation table. Carefully clean up the installation table without oil, dust, iron and so on. The magnetic stripe gradually attached to the adhesive parallel installation table. The magnetic stripe strip parallel to the gum protection gradually attached to the surface of the magnetic stripe. Attention: not close to the strong magnetic, or damage the magnetic strip. Posted: will be posted on the magnetic stripe clean equipment installation, will protect the strip affixed to the surface in the black stripe, AB glue sealed at both ends of the magnetic stripe. Read the number head. The feeler (1.5mm) sandwiched between the magnetic stripe and the reading head, with M3 screws readheads will remove feeler. Observe the direction of measurement data. On the contrary, change the direction of the data through the P02. Determine the initial display value. The initial position value can be set and transferred through the P01. At the same time press the “C” + “F” key to adjust the set value of the P01 menu, that is, the initial value reset function (“clean zero”). LCD backlight key is pressed, the backlight automatically closes after 5 seconds if the measurement data is not changed, otherwise the backlight is often turned on until it is pressed again. When installing this product, if the deviation is too large, it will affect the use precision and even can not be used. Please do not corrode, acid, alkali, direct sunlight, etc. Which exceed the environment requirements, otherwise it may cause trouble. The bending radius of the reading head must be greater than 25mm. The installation of this equipment should be more than 0.5 meters above the circuit breaker, relay, electric motor capacitance, brake, clutch, frequency converter and so on. The cable direction must be separated from the power line to reduce the noise in the string. Thank you for your support. We are not responsible for undeliverable address. Dear friend, your happy is very important to me! . We stand behind every product we sell. You can enjoy top-quality product and high-quality services from us, Trust me that you will have a pleasant shopping experience in here. We will be happy to assist you. We would try our best to serve you with any question / problem.
Shars. 0002 XYZ 3AXIS DRO DIGITAL READOUT GLASS LINEAR QUILL MILLING PACKAGE R
3 AXIS X Y Z DRO DIGITAL READOUT GLASS LINEAR QUILL MILLING PACKAGE NEW. 3 Axis For Milling Machine (X, Y, Z). 8″ x 20″ x 6. 10″ x 24″ x 6. 12″ x 24″ x 6. 12″ x 32″ x 6. 12″ x 36″ x 6. 12″ x 38″ x 6. 14″ x 24″ x 6. 13″ x 32″ x 4. 13″ x 35″ x 4. 14″ x 30″ x 6. 14″ x 32″ x 6. 14″ x 36″ x 6. 16″ x 32″ x 6. 16″ x 36″ x 4. 16″ x 36″ x 6. 16″ x 40″ x 6. 18″ x 40″ x 6. 7 digits with plus or minus symbol. Absolute/Relative coordinate display mode. Center Find / ½ Function. User defined memory storage coordinates up to 200 points. Self Diagnostics in start up. Programmable resolution setting by Axis. Programmable direction by Axis. Power consumption: DC 5V (+/15%) 80 MA. Math calculator (including trigonometric). Glass Scale Linear Encoder Features. Accuracy of +/-0.0002 (+/- 5 um) +/. 0004 (+/- 10 um). TTL signal output, 9 pin socket. Digital Reader head with armored cable and installation arm. 3 Linear glass scales. Scale, scale cover, and scale support brackets.
ONE M503 Magnetoscale LCD Digital Readout Meter for stCutting tool NEW
ONE M503 Magnetoscale LCD Digital Readout Meter for stCutting tool NEW. 1.7 bit LCD display that it is more suitable for long travel equipment. High contrast backlight, clear and eye-catching. Low power consumption, no external power supply (built-in two nodes 5 battery). Repetition precision can be up to + 0.01mm. 5 initial value reset function (“clean zero”). Optional millimeter mm/ inches inch. Optional relative REL/ absolute ABS. Optional linear measurement / angle measurement. System precision: ±0.03+0.01L(m) mm. Resolution: 0.01, 0.05, 0.1, 1. Display range: -1999999 9999999. Consumption of current: Max. Power: two AA battery. Reading head and line length: default 1m. Reading head gap: Max. 2.5mm, recommending 1.5mm. Matching magnetic ruler: MS50. Waterproof grade: digital display IP40, reading head IP65. Ensure the parallelism of the installation table. Carefully clean up the installation table without oil, dust, iron and so on. The magnetic stripe gradually attached to the adhesive parallel installation table. The magnetic stripe strip parallel to the gum protection gradually attached to the surface of the magnetic stripe. Attention: not close to the strong magnetic, or damage the magnetic strip. Posted: will be posted on the magnetic stripe clean equipment installation, will protect the strip affixed to the surface in the black stripe, AB glue sealed at both ends of the magnetic stripe. Read the number head. The feeler (1.5mm) sandwiched between the magnetic stripe and the reading head, with M3 screws readheads will remove feeler. Observe the direction of measurement data. On the contrary, change the direction of the data through the P02. Determine the initial display value. The initial position value can be set and transferred through the P01. At the same time press the “C” + “F” key to adjust the set value of the P01 menu, that is, the initial value reset function (“clean zero”). LCD backlight key is pressed, the backlight automatically closes after 5 seconds if the measurement data is not changed, otherwise the backlight is often turned on until it is pressed again. When installing this product, if the deviation is too large, it will affect the use precision and even can not be used. Please do not corrode, acid, alkali, direct sunlight, etc. Which exceed the environment requirements, otherwise it may cause trouble. The bending radius of the reading head must be greater than 25mm. The installation of this equipment should be more than 0.5 meters above the circuit breaker, relay, electric motor capacitance, brake, clutch, frequency converter and so on. The cable direction must be separated from the power line to reduce the noise in the string. Thank you for your support. We are not responsible for undeliverable address. Dear friend, your happy is very important to me! . We stand behind every product we sell. You can enjoy top-quality product and high-quality services from us, Trust me that you will have a pleasant shopping experience in here. We will be happy to assist you. We would try our best to serve you with any question / problem.
(200 And 400mm)Digital Readout DRO 2 Pcs Lathe Linear Scale 2AE/3AE Axis
Repeat positioning measurements, the data is accurate and stable. Made of aluminum alloy profiles, alloy die-casting, corrosion resistant. This ruler is suitable for JCS900-2AE/JCS900-3AE digital display. Compact and practical design makes it work more stable. 5um accuracy and resolution for convenient and accurate measuring. Item Type:Linear Scale Material:Aluminum Alloy Model:JCS900-2AE/JCS900-3AE Accuracy:+-5um Resolution:5um Type:Linear Scale Measuring Range:(Optional) 0200mm and 0350mm 0200mm and 0400mm 0200mm and 0450mm. 2 x Linear Scale. 2 Set Mounting Accessory. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.
Used Anilam Wizard 211 2-Axis Digital Readout (A221200)
The Anilam Wizard 211 comes with the following features.. 1, 2 and 3 axes.
With Precision Linear Scale New Digital Readout 2 Axis For Milling Lathe Mach mw
We are a professional supplier of industrial control parts. We have a lot of products and only show a small number of products on the website. Item contains: One item. If you have any question, please contact me directly. Instead of opening CASE. That brings us very bad effect and can’t solve any problem. We will give big discount for the future business. The buyers who directly open cases without contacting us first! Thank you for taking the time to shop with us. We realise that you want your stuff as soon as possible. That’s why we are committed to making sure that your order will leave our warehouse in time. Orders will be dispatched with China post or one of our designated courier services. Unfortunately we are unable to dispatch on the weekends or holidays. The item must be unused and must be in the same condition as it was dispatched from our warehouse. We will endeavour to respond within 24 hours. We are fully comitted to your complete satisfaction, so if anything isn’t clear, just get in touch. Our opening times are 08:00 – 20:00 Monday – Friday.